= Errata/ Things we had to change but haven't formally committed to documentation = === 10/11/2010 === We're going down the list of wiki:WiMAX/Software/Configuration and editing all the files accordingly. * on the console machine (10.3.7.254 in this case), we edited /usr/share/asngw/classify-ctrl.sh, we changed the lines:[[BR]] Changed: {{{ : ${DEV_R3:="eth0"} : ${DEV_R6R4:="eth1"} : ${DEV_GREALL:="gre+"} : ${DEV_MSTUN:="mstun"} : ${MS2MS:="DROP"} : ${MS2MS_GRE_OPT:=""} : ${MS2MS_MSTUN_OPT:="-p icmp"} : ${MSMARK:="0x100"} : ${MSADDR:="10.41.0.0/16"} : ${R3_NETWORK:="10.41.0.0/16"} : ${R3_ADDR:="10.41.0.3"} #jml : ${R6R4_NETWORK:="10.3.0.0/16"} : ${R6R4_ADDR:="10.3.7.1"} # jml }}} * editing the asnctrl.conf[[BR]] Changed: {{{ R6_BSID[0] = 44:51:DB:00:07:01 R6_BSAddress[0] = [10.3.7.1]:2231 TunnelEndpoint = [10.3.7.254]:0 }}} * editing the asnctrl_ASNGW000.conf[[BR]] Changed {{{ R4_BSID[0][0]=44:51:DB:00:07:01 }}} * epctr.conf {{{ R3LocalDevice = eth0 R4LocalDevice = eth1 R6LocalDevice = eth1 }}} ---- We discovered an error in the wiset commands. Apparently the IP of the authgw_ip and associated flags needs to be set to the IP of the consoles eth1 intefaces (the one in the BS subnet). I had it incorrectly set to point to it self. {{{ wiset authgw_ip 0x0A0307FE wiset asngw_dp_ip 0x0A0307FE wiset asngw_ep_ip 0x0A0307FE }}} Was run. ---- We copied SAMrb (cons-wm-01:/root/Oldhome/SAMrb_Oct7_2010.tar) from cons-wm-01 to the /root of the console and untarred it. We then installed rubygems and the open4 and orderedhash gems. {{{ 240 apt-get install rubygems 242 gem install open4 243 gem install orderedhash }}} From here we run the simple authmanager, it's interpreted by the ruby interpreter. {{{ root@wimax:/root/SAMrb# ruby SimpleAuthManager.rb Writting to a file Started click PID=4633 }}} ---- The last step is to check if connectivity work by associating a wimax client. '''NOTE''' the power of the ODU connected to the test BS is very low, the client should be very close to the antenna, and the other BS (ours) must be turned off. On the client (imaged with appropriate drivers, wimax utils, etc.. ), run {{{ wimaxcu ron - turns on the raido wimaxcu scan - scans for the BS wimaxcu connect profile 51 }}} you should see a connected message. If you want to reset the radio run: {{{ wimaxcu ron wimaxcu roff }}} ---- === 10/12/2010 === In order to connect to the serial console for managment, you'll need a straight through (not null) serial cable that connects male to female. You'll also need mini-com Installed (apt-get-able). From the default mini-com install, edit the config (ctrl-a, o) and change the default port to '''/dev/ttyS0'''. The default transmit paramters are ok, '''115200,8,N,1'''. You will howerver need to '''disable hardware flow''' control to talk to the DSP machine. Save these as a default.