close
Warning:
Can't synchronize with repository "(default)" (/common/SVN/wimax does not appear to be a Subversion repository.). Look in the Trac log for more information.
- Timestamp:
-
Apr 23, 2014, 8:06:27 PM (9 years ago)
- Author:
-
seskar
- Comment:
-
—
Legend:
- Unmodified
- Added
- Removed
- Modified
-
v13
|
v14
|
|
3 | 3 | [[TOC(Internal/*)]] |
4 | 4 | |
5 | | Please make sure that you have the [attachment:MiMAX-Pro_AWB_RG231_81-1.0.3.2-5.2.7.3.zip latest firmware] installed before configuring the device; the firmware upgrade procedure is described in the [attachment:'MiMAX-Easy (RG231)_User_Guide.pdf' user guide]. |
| 5 | Please make sure that you have the [attachment:MiMAX-Pro_AWB_RG231_81-1.0.3.2-5.2.7.3.zip latest firmware] installed before configuring the device; the firmware upgrade procedure is described in the [attachment:'MiMAX-Easy (RG231)_User_Guide.pdf' user guide]. By default, the device has fixed IP address of '''192.168.1.1'''; set your machine to any 192.168.1.X address and connect it to the gateway with the Ethernet cable. Management is mostly done over http at port 80 (but can be also performed over the [wiki:Internal/WimaxRG231#telnet telnet session]). |
6 | 6 | |
7 | 7 | == GENI Configuration == |
… |
… |
|
26 | 26 | The filled-in page should look like the one shown in Figure 2 and 3. |
27 | 27 | |
28 | | [[Image(Profile1.jpg)]] |
29 | | [[Image(Profile2.jpg)]] |
| 28 | [[Image(Profile1.jpg, width=600)]] |
| 29 | [[Image(Profile2.jpg, width=600)]] |
30 | 30 | |
31 | 31 | Select '''Apply''' button in the upper right corner. |
32 | 32 | |
33 | 33 | B. ('''optional but recommended''') Select the '''Operator List''' on the sub-menu and add newly created operator (for the operator from the example above it would be: |
34 | | 1. Operator Name: '''44:51:db''' |
| 34 | 1. Operator ID: '''44:51:db''' |
35 | 35 | 1. Operator Name: '''GENI''' |
36 | 36 | 1. Enable: checked |
37 | 37 | and hit '''Add''' button (Figure 4). |
38 | 38 | |
39 | | [[Image(Operator.jpg)]] |
| 39 | [[Image(Operator.jpg, width=600)]] |
40 | 40 | |
41 | | C. Reboot the gateway (the '''Reboot''' button should have appeared above the menu once you applied "Profile Settings"; otherwise go to '''System''' and select '''Restart''' ). |
| 41 | C. Chose the type of the basestation you are connecting to by selecting '''Advanced Config''' on the sub-menu and then choosing the BS type from the pull-down meny. Default settings shouls work for both NEC and Airspan BSs. The browser snapshots for both BS types are shown in the table below. |
| 42 | |
| 43 | ||= NEC =||= Airspan =|| |
| 44 | || [[Image(Nec.jpg, width=300)]] || [[Image(Airspan.jpg, width=300)]] || |
| 45 | |
| 46 | D. Reboot the gateway (the '''Reboot''' button should have appeared above the menu once you applied "Profile Settings"; otherwise go to '''System''' and select '''Restart''' ). |
| 47 | |
| 48 | === Telnet Management === #telnet |
42 | 49 | |
43 | 50 | The device is actually an [https://openwrt.org/ OpenWRT based gateway]; you can telnet into it with: |