wiki:cLTE/cHardware/cAirSynergy
close Warning: Can't synchronize with repository "(default)" (/common/SVN/wimax does not appear to be a Subversion repository.). Look in the Trac log for more information.

Version 18 (modified by jkol, 8 years ago) ( diff )

—

AirSynergy 2000

Table of Contents

    1. Hardware
      1. Base Station (eNodeB)
      2. User Equipment (UE)
      1. AirSynergy 2000
        1. Hardware Installation
          1. Power Supply
            1. Power Supply Connector/Cable
          2. Compatible SFP+ Adapters
            1. CAT5/CAT6 (Copper Gigabit Ethernet)
            2. Multi-mode Fiber
            3. Single-mode Fiber
          3. Serial Debug
        2. Software Installation

Hardware Installation

AirSynergy Connections:

No image "Slide1.PNG" attached to cLTE/cHardware/cAirSynergy

1. Power Connect power cable to -48 power supply with the provided cable; [Mean Well SP3XXX] No image "Slide2.PNG" attached to cLTE/cHardware/cAirSynergy
2. Networking Insert SFP+ and connect; list of supported SFP+s
3. Serial Console (optional) If needed for debugging

Fully connected AirSynergy without weatherproofing covers should look like this:

No image "as2000-populated.jpg" attached to cLTE/cHardware/cAirSynergy


Power Supply

The AirSynergy supports direct connection to a -48VDC nominal power source.
Operating Voltage Range: -40.5 to 57 VDC

A power supply capable of 2A or greater is recommended (eg. Mean Well CLG-100-48).

Power Supply Connector/Cable

The base station end of the power supply cable uses a Molex 0039012040 housing (Digikey: ​WM3701-ND) with Molex 0039000039 pins (Digikey: ​WM2501-ND). The power supply cable itself is 4-conductor 16 AWG.

Power Connector Housing:

No image "airsynergy_power_connector_housing.png" attached to cLTE/cHardware/cAirSynergy

Power Connector Pinout:

No image "airsynergy_power_connector_pinout.jpg" attached to cLTE/cHardware/cAirSynergy


Compatible SFP+ Adapters

The following SFP+ adapters were tested for compatibility with the AirSynergy.

NOTE: Fiber connections were tested with the following adapters on the "server" side:

Manufacturer Model Note
Intel FTLX8571D3BCV-IT multi-mode fiber
Intel FTLX1471D3BCV-IT single-mode fiber
CAT5/CAT6 (Copper Gigabit Ethernet)
Manufacturer Model Note
Avago ABCU-5730ARZ 1G (T)
Multi-mode Fiber
Manufacturer Model Note
Dell FTLX8571D3BCL 1G/10G (SR)
Finisar FTLX8571BCV
Intel AFBR-703SDZ-IN2
Iwnetworks IW-TRSFPL-SR
Finisar SFP-10GSR-85
Trendnet TEG-MGBSX
Cisco 1000BASE-SX
Single-mode Fiber
Manufacturer Model Note
Dell FTLX1471D3BCL


Serial Debug

The base station has a 9 pin connector (hidden behind a black hex bolt next to the port marked "ETH") which allows access to the serial. This is useful for recovery purposes when the base station does not respond via software, SSH, or web interfaces. See Airspan LTE Base Station Serial Console for information on cable construction and serial port parameters. Note that the AirSyngery only has the "asil8xx" serial port functioning (TX2,RX2 in the referenced document). However, the other internal module can still be accessed via ssh once logged into the asil8xx module via the serial port.


Software Installation

TODO

Attachments (3)

Download all attachments as: .zip

Note: See TracWiki for help on using the wiki.